|
|
Location: Home / DIY tools / Cordless Drills / Draper 41407
Draper 41407
14.4V COMBI C/LESS DRILL-2 BATT (Barcode EAN = 5010559414079).
|
|  | $156.99 Draper LVC-III Control Switch 
Two double-gang electrical boxes bolted together. One box contains the actual module, while the empty box is useful for making connections. The module contains a 3-screw terminal block for a wall switch (up, down, common), IR receiver jack, RF receiver jack, and a user-serviceable 6.3A fuse. A spare fuse is included. There is a 6-wire pigtail for Hot, Neutral, Ground, Common, Up and Down. Rakuten.com Shopping |
| | $74.74 Niagara Cutter 41407 High Speed Steel (HSS) Square Nose End Mill, Inch, Weldon Shank, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 5.5 Overall Length, 1.250 Cutting Diameter, 1.250 Shank Diameter 
The Niagara Cutter SC406 uncoated high-speed steel square end mill has a 30-degree helix angle for general-purpose machining on a range of materials. The number of flutes varies; fewer flutes provide better chip-carrying capacity, while more flutes produce a finer finish. High-speed steel (HSS) is a common general-purpose steel for cutting tools and is compatible with a variety of materials. With no coating or surface treatment, this uncoated tool can be used on a broad range of materials. The tool’s square end creates sharp, unrounded cuts. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit, and used for applications such as profiling and slotting. The cutting diameter tolerance is +0.001” to -0.000”. This tool has a Weldon shank. End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts. Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive. Amazon |
| | | |
|
| * Expert Quality | * Spindle lock for easy bit change | * Variable speed control | * 22position torque control | * Two speed gearbox | * 13mm jacobs keyless chuck | * Electric brake | * forward/reverse facility | * Soft grip handle and trigger |
Where to Buy Online
Click on the shop name to visit their website and buy this product
(cheapest price in red).
(note: Please make sure you double check the product details on the shop's site BEFORE you order the
Draper 41407 and also read our Accuracy of Product Information statement below.
)
|
|
| | Draper LVC-III Control Switch
Two double-gang electrical boxes bolted together. One box contains the actual module, while the empty box is useful for making connections. The module contains a 3-screw terminal block for a wall switch (up, down, common), IR receiver jack, RF receiver jack, and a user-serviceable 6.3A fuse. A spare fuse is included. There is a 6-wire pigtail for Hot, Neutral, Ground, Common, Up and Down. Rakuten.com Shopping |
| | Niagara Cutter 41407 High Speed Steel (HSS) Square Nose End Mill, Inch, Weldon Shank, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 5.5 Overall Length, 1.250 Cutting Diameter, 1.250 Shank Diameter
The Niagara Cutter SC406 uncoated high-speed steel square end mill has a 30-degree helix angle for general-purpose machining on a range of materials. The number of flutes varies; fewer flutes provide better chip-carrying capacity, while more flutes produce a finer finish. High-speed steel (HSS) is a common general-purpose steel for cutting tools and is compatible with a variety of materials. With no coating or surface treatment, this uncoated tool can be used on a broad range of materials. The tool’s square end creates sharp, unrounded cuts. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit, and used for applications such as profiling and slotting. The cutting diameter tolerance is +0.001” to -0.000”. This tool has a Weldon shank. End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts. Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive. Amazon |
| | | |
Newsletter
Join our
mailing list and be kept informed of product news and SPECIAL OFFERS.
|
|
|
|
Accuracy of Product Information
All product features, images, prices and other information published on our website have either been made accessible by suppliers or been gathered from public-domain sources. Advanced System Technologies Ltd. makes every effort to ensure all information on this website is as accurate and up to date as possible. However, Advanced System Technologies Ltd. cannot guarantee the reliability or the accuracy of the information contained within its pages. All the actions taken by the user of the website are the responsibility of the individual.
Copyright © 1999,2013 Advanced System Technologies Limited. All Rights
Reserved.
All information on this site is presented as a guide. Advanced System Technologies Ltd. accepts no responsibilty for the accuracy of any information contained on the pages within this site.
|
The CompareStorePrices.co.uk device is a registered trademark of Advanced System Technologies Limited.
All other trademarks and devices are the property of their respective owners.
|
Vouchers Feed
More Draper Cordless Drills